Thetriplepointsofneonandcarbondioxideare24.57Kand216.55Krespectively. ExpressthesetemperaturesontheCelsiusandFahrenheitscales.

Two absolute scales A and B have triple points of water defined to be 200 A and 350 B. What is the relation between T_A and T_B?

The electrical resistance in ohms of a certain thermometer varies with temperature according to the approximate law: R = R_o [1 + a (T – T_o)] The resistance is 101.6 O at the triple-point of water 273.16 K, and 165.5 O at the normal melting point of lead (600.5 K). What is the temperature when the resistance is 123.4 O?

Two ideal gas thermometers Aand Buse oxygen and hydrogen respectively. The following observations are made: Temperature Pressure thermometer A Pressure thermometer B Triple-point of water 1.250 × 10⁵ Pa 0.200 × 10 Pa Normal melting point of sulphur 1.797 × 10⁵ Pa 0.287 × 10 Pa What is the absolute temperature of normal melting point of sulphur as read by thermometers Aand B? What do you think is the reason behind the slight difference in answers of thermometers Aand B? (The thermometers are not faulty). What further procedure is needed in the experiment to reduce the discrepancy between the two readings?

A steel tape 1m long is correctly calibrated for a temperature of 27.0 °C. The length of a steel rod measured by this tape is found to be 63.0 cm on a hot day when the temperature is 45.0 °C. What is the actual length of the steel rod on that day? What is the length of the same steel rod on a day when the temperature is 27.0 °C? Coefficient of linear expansion of steel = 1.20 × 10^–5K^–1.

A large steel wheel is to be fitted on to a shaft of the same material. At 27 °C, the outer diameter of the shaft is 8.70 cm and the diameter of the central hole in the wheel is 8.69 cm. The shaft is cooled using ‘dry ice’. At what temperature of the shaft does the wheel slip on the shaft? Assume coefficient of linear expansion of the steel to be constant over the required temperature range: a_steel = 1.20 × 10^–5 K^–1.

A hole is drilled in a copper sheet. The diameter of the hole is 4.24 cm at 27.0 °C. What is the change in the diameter of the hole when the sheet is heated to 227 °C? Coefficient of linear expansion of copper = 1.70 × 10^–5 K^–1.

A brass wire 1.8 m long at 27 °C is held taut with little tension between two rigid supports. If the wire is cooled to a temperature of –39 °C, what is the tension developed in the wire, if its diameter is 2.0 mm? Co-efficient of linear expansion of brass = 2.0 × 10^–5 K^–1; Young’s modulus of brass = 0.91 × 10¹¹Pa.

A brass rod of length 50 cm and diameter 3.0 mm is joined to a steel rod of the same length and diameter. What is the change in length of the combined rod at 250 °C, if the original lengths are at 40.0 °C? Is there a ‘thermal stress’ developed at the junction? The ends of the rod are free to expand (Co-efficient of linear expansion of brass = 2.0 × 10^–5 K^–1, steel = 1.2 × 10^–5 K^–1).

The coefficient of volume expansion of glycerin is 49 × 10^–5 K^–1. What is the fractional change in its density for a 30 °C rise in temperature?

A 10 kW drilling machine is used to drill a bore in a small aluminium block of mass 8.0 kg. How much is the rise in temperature of the block in 2.5 minutes, assuming 50% of power is used up in heating the machine itself or lost to the surroundings. Specific heat of aluminium = 0.91 J g^–1 K^–1.

A copper block of mass 2.5 kg is heated in a furnace to a temperature of 500 °C and then placed on a large ice block. What is the maximum amount of ice that can melt? (Specific heat of copper = 0.39 J g^–1 K^–1; heat of fusion of water = 335 J g^–1).

In an experiment on the specific heat of a metal, a 0.20 kg block of the metal at 150 °C is dropped in a copper calorimeter (of water equivalent 0.025 kg) containing 150 cm³ of water at 27 °C. The final temperature is 40 °C. Compute the specific heat of the metal. If heat losses to the surroundings are not negligible, is your answer greater or smaller than the actual value for specific heat of themetal?

Givenbelowareobservationsonmolarspecificheatsatroomtemperatureofsome commongases. Gas Molar specific heat (Cv) (cal mol^–1 K^–1) Hydrogen 4.87 Nitrogen 4.97 Oxygen 5.02 Nitric oxide 4.99 Carbon monoxide 5.01 Chlorine 6.17 The measured molar specific heats of these gases are markedly different from those for monatomic gases. Typically, molar specific heat of a monatomic gas is 2.92 cal/mol K. Explainthisdifference.Whatcanyouinferfromthesomewhatlarger(thantherest)value forchlorine?

A child running a temperature of 101°F is given an antipyrin (i.e. a medicine that lowers fever) which causes an increase in the rate of evaporation of sweat from his body. If the fever is brought down to 98 °F in 20 min, what is the average rate of extra evaporation caused, by the drug? Assume the evaporation mechanism to be the only way by which heat is lost. The mass of the child is 30 kg. The specific heat of human body is approximately the same as that of water, and latent heat of evaporation of water at that temperature is about 580 calg^–1.

A ‘thermacole’ icebox is a cheap and efficient method for storing small quantities of cooked food in summer in particular. A cubical icebox of side 30 cm has a thickness of 5.0 cm. If 4.0 kg of ice is put in the box, estimate the amount of ice remaining after 6 h. The outside temperature is 45 °C, and co-efficient of thermal conductivity of thermacole is 0.01 J s^–1 m^–1 K^–1. [Heat of fusion of water = 335 × 10³ Jkg^–1]

A brass boiler has a base area of 0.15 m² and thickness 1.0 cm. It boils water at the rate of 6.0 kg/min when placed on a gas stove. Estimate the temperature of the part of the flame in contact with the boiler. Thermal conductivity of brass = 109 J s ^–1 m^–1 K^–1; Heat of vaporisation of water = 2256 × 10³ Jkg^–1.

Explain why: a body with large reflectivity is a poor emitter a brass tumbler feels much colder than a wooden tray on a chilly day an optical pyrometer (for measuring high temperatures) calibrated for an ideal black body radiation gives too low a value for the temperature of a red hot iron piece in the open, but gives a correct value for the temperature when the same piece is in the furnace the earth without its atmosphere would be inhospitably cold heating systems based on circulation of steam are more efficient in warming a building than those based on circulation of hot water

A body cools from 80 °C to 50 °C in 5 minutes. Calculate the time it takes to cool from 60 °C to 30 °C. The temperature of the surroundings is 20 °C.